This is one of the toughest calls for any raid leader to make. But it’s one of the best ways to optimize your raiding time and not waste any more effort or consumables trying to prolong a fight that’s already lost. I know some of you may think “Never! No surrender!” but really, it is a futile effort if your MT dies or over 50% of your healers are dead, or some other crap hits the fan. I want to give an example of a wipe procedure since not many young Guilds have such a concept in mind. Many inexperienced Guilds will continue to engage to the bitter end.
What, you thought Warlocks were only good for Healthstones and DPS? No, they have Soulstones which when applied to any player allows them to resurrect themselves whenever they like. If that player falls in combat when the entire raid is still alive, it’s best to blow it. When you are engaging raid bosses, operate as if you are not going to wipe unless it is painfully obvious. So again, blow the stone. If you’re the last man standing, don’t blow the stone.
I sympathize with the Raid Leader when it’s called. It’s not a very decision to make and a false call will involve a waste of over hundreds of gold in repair bills and consumables. The correct call will save time and allow for more attempts. Typically, your Raid Leader will announce a wipe. When that happens, the following should happen: Ranged DPS would run to a location where they can be easily picked up (Such as the Gate when engaging Gruul). Try to get a Priest, Shaman, or Paladin in that same position and have a Paladin use their Divine Intervention to render that player immune. Shaman’s have the ability to self resurrect themselves, but that is an ability which should be used if the other two options are available. If you want to be really crafty, get a Druid outside in a clear position from where he can Battle Res a healer. Generally that is not recommended since it can be put to better use during combat. But if you’re in a raid instance and mobs start to respawn in ten minutes, you may not have the time or energy to reclear it all. Make sure that healer doesn’t accept it until after the encounter is reset. The moment wipe protection is utilized, make sure it’s called in vent so that players know. If there isn’t one, the last thing to do is the walk of shame back from the graveyard.
So to summarize in the following order:
* Shammy Res
* Fancy Druid maneuver
Post Wipe and Analysis
Your Stoned healer picks himself up and starts ressing other healers OR Your DI’d player clicks off the buff (debuff?) and starts ressing other healers OR Your Shaman activates his self res and starts ressing other healers OR your Battle Res’d Healer wakes up and starts ressing other healers.
See a pattern here? Let your tanks and melee run back since most of the time you won’t be able to pick them up without drawing Aggro. If you can get a player, call it out in vent so they don’t zone in and be forced to run the gauntlet.
As players are being ressed, buffed, and positioned for the next attempt, go over the encounter and figure out what happened. What is a badly timed misheal? A crit from a mage which pulled aggro? The tank not eat his Wheaties that morning? Figure out what the problem is and remedy it, or else it will happen again. Raid Leaders should not be afraid to reassign healers to different assignments. Some healers are better tailored for certain jobs then others. Maybe you want your veteran healers to focus more a bit on the clothies during some phase where they take damage (Mage tank in Gruul’s lair). Sometimes you need to mix and match. But more importantly, analyze what your mistakes were so that they don’t happen again. If the fault was the result of a player, don’t call it out in raid but allow them to speak up and take responsibility. It shows signs of maturity and trust. If no one admits fault but you know who it is, send them a light whisper letting them know that they forgot an assignment or made a mistake because some players just aren’t aware that did anything wrong.
Sometimes, I wish Blizzard would implement an Instant Replay function with speed up and slow down functions so certain phases can be analyzed.